Recently we have formed a Joint venture with a Belgium company to manufacture Metal o-ring seals. Here is the information on seals to be manufactured.
General Information
High Performance Seals for extreme service conditions.
HTMS resilient Metal Seals are designed and produced to provide the required tightness, when subjected to extremes of temperatures, pressure and media.
HTMS metal seals are produced from stainless steel or high temperature alloy tubing, strip and wire.
Engineering
Development and Engineering of new products is conducted in close cooperation with universities.
In house testing equipment facilitates real hardware testing and comparison with FEA results.
The Oysterseal® in this catalogue is one of the results of this bespoken cooperation.
Sealing Concept:
The sealing performance of resilient Metal Seals is based on a the relative high specific contact load at the sealing line and a certain resiliency or spring back of the elastic metal seal.
The seating load and the corresponding sealing line width, are a function of the selected seal type, cross section, material, material thickness and the alloy properties itself.
General Properties:
Sizes: Diameters from 5 mm to 7 meter.
Cross section from 0,8 mm to 12,5 mm.
Temperature: Cryogenic to 750°C.
Pressure: From ultra high vacuum to 500 MPa.
Available in circular, race track, oval and other shapes.
Excellent resistance to corrosion and radiation.
Maintains elasticity or spring back over an extended service life.
Does not suffer from explosive decompression.
Capable of reaching tightness better than 10–9 mbar.l/s.
Radiation resistant.
Material Selection:
The application parameters determine which material should be used.
Temperature and media are important aspects in selecting the material.
HTMS offers materials such as 321 stainless steel, Inconel® and other high temperature alloys.
|
 | Metal O-Ring | | |
Specifications and Applications
The metal o-ring seals of Kwality products can be used where non-metallic seals will not seal properly or do not offer the required reliability for the application, usually due to temperatures, pressures, or the environment. Metallic O-Ring Seals are long lasting seals and unlike non-metallic seals, they are not subject to failure due to incompatibility with the environment, out gassing or from deterioration due to age.
O-Ring Seals are generally fabricated from tubing consisting of stainless steel or high temperature alloys such as Inconel (currently in development). These materials are frequently used because they offer resilient properties that enable the seal to "Spring-Back".
Hollow metal O-Rings are used as static face type seals and should not be used as a dynamic seal. While the majority of seals are circular, many seals are produced in rectangular, racetrack, and other various shapes and configurations with limitations only on the corner radii.
The following are key elements in specifying the proper seal determining the base material:
- Temperature limits/duration
Plating and Coatings
Plating or Coating of the O-Ring Seal provides a soft malleable surface that will smear into small imperfections in the mating hardware, enhancing seal performance.
Shaped Seals
Metallic O-ring Seals can be produced in various shapes.
Application Characteristics
The typical application places a Metallic O-Ring Seal in an axial compression between two parallel surfaces, which are square to the fluid passage or vessel axis. The seal is usually located in an open or closed groove in one of the surfaces. The seal can also be located in a retainer, which eliminates the need for machining a groove. The mating hardware when bolted, torque, clamped or fastened tightly to the surface enclosing the ring, compresses the seal, forming a positive joint
O-Seals are commonly used in the following industries.
- Oil and petrochemical industries
- Vacuum Processing/Research
Kwality Products can also make following seals available to there customers through there Joint venture partners | 
|
| Metal C-rings | | |
- Metal C-Ring for Internal Pressure
- Metal C-Ring for External Pressure
- Metal C-Ring for Internal Pressure (CI) and External Pressure (CE) are designed for high pressure (system pressure energised). They require low bolting load and have good spring back.
Metal Spring energized C-rings:
- Spring Energised C-Ring for Internal Pressure
- Spring Energised C-Ring for External Pressure
- Metal CS-Ring for Internal Pressure (CSI) and External Pressure (CSE) are designed for high pressure and excellent tightness performance (system pressure energised). They require high bolting load and have good spring back.
|
|
|
 Product
Showcase View all our products / services as a slide show. play now
|
